RETROSOUND radio module (FM/DAB+) including installation material

The article "MOTOR-1DAB" is the entry-level product for digital radio reception at RetroSound. Radio module with all cables and accessories but without the display unit. The display unit, the control knobs and the rear control rings must be ordered separately.

Of course, the "MOTOR-1DAB" radio module also has the flexible "InfiniMount" mounting system and control knobs patented by RetroSound. With this unit, you get the design of your classic and do not have to do without modern digital media. An AUX input (3.5mm jack) on the back of the unit allows you to add external audio players or a Bluetooth receiver.

Any concerns that the installation of a RetroSound car radio might jeopardise your H-licence plate are unfounded. In the download you will find a confirmation with the approval of the complete AKE working group (TÜV SÜD, TÜV Rheinland, TÜV Nord, Dekra, KÜS, GTÜ) which states that the "RetroSound Model Zuma" and the "RetroSound Model Two" including vehicle-specific panel and control buttons may be installed in classic cars with H-plates or do not prevent the award of the H-plate!

EQUIPMENT
- Warm white LCD lighting
- DAB+/UKW/MW radio receiver with RDS and 30 station memory
- Tuner with European even and odd radio frequencies
- Integrated 4-channel amplifier (4 x 18 watts RMS)
- 3 equaliser programmes plus individual bass/treble/fader/balance adjustment
- E-approval e13 03 10006 e13*72/245*2006/96*10006*00
- XBAS loudness function
- Non-volatile memory

EXPANSION OPTIONS
- 1 AUX input (stereo) with 3.5 mm jack socket on the rear of the unit
- Separate power cable for motor aerial and amplifier

TECHNICAL DATA RADIO SECTION
- VHF European broadcasting Frequency range 87.5-107.9 MHz. (0.05 MHz. in steps)
- MW frequency range 530-1710 kHz (9 kHz. in steps)
- DAB+ reception via SMB antenna input for passive DAB+ antennas

SCOPE OF DELIVERY
- Radio base module with FM/DAB+ receiver
- Main wiring harness
- ISO connection cable (power & loudspeaker harness)
- Screw and fixing material
- Spacer washers
- Mounting plate with accessories
- Mounting bracket

GENERAL DATA
- Dimensions of basic radio unit 101x51x136mm
- Power supply 10.5 to 14.4 volts
- Maximum current consumption 15 amps
- Quiescent current 3.5 mA
- Output power 12V, 4 Ohm, <1% distortion: 4x18 Watt (RMS)
- Loudspeaker impedance 4-8 Ohm
- Input sensitivity AUX1 >300 mV / 6 kOhm

E-APPROVAL
- E-approval e13 03 10006 e13*72/245*2006/96*10006*00

VEHICLES WITH 6 VOLT ELECTRICAL SYSTEM
You need a voltage converter if you want to operate a RetroSound car radio in a vehicle with a 6 volt electrical system. We recommend the DC/DC converter 2238.0 from Statron (www.statron.de) in such a case.

*IMPORTANT NOTE
Please order the display unit and control knobs for your car separately. These are not included with the car radio.

COMPATIBLE DISPLAY UNITS
- APACHE
- DALLAS
- DAYTONA
- DETROIT
- EUROPE
- GRAND PRIX
- HUNTINGTON
- MONTEREY
- NEW YORK
- NEWPORT
- REDONDO-S
- RETRO-RADIO-B
- RETRO-RADIO-BC
- RETRO-RADIO-C
- RETRO-RADIO-CB
- RETRO-RADIO-IVO
- SANTA CRUZ
- WONDERBAR WB1
- WONDERBAR WB2

NON-COMPATIBLE DISPLAY UNITS
- REDONDO-T

OTHER SEARCH TERMS
RETROSOUND, retrosound, Zuma, zuma, ZUMA, Hermosa, hermosa, HERMOSA